It’s finished! I have been teasing you all for quite some time now about this French chair project.
It was a thrift store find, and I was excited to try my hand at upholstery again after working on a French Settee last summer. The chair’s structure was sound, but the wood was scratched and faded and the fabric was well, terrible. Now here it is after a paint and re-paint, and with new, modern fabric.
It’s pretty amazing! I promised a walk-through of the process, so here we go. Warning in advance, there are alot of pictures!
First step in any upholstery project is removing the old fabric. I started with pulling out the buttons, then, using some needle nose pliers, slowly ripped off the trim.
Don’t rip too hard or too fast, you want to try and keep the fabric intact. Some of the upholstery nails and staples will come out with the fabric along the way, some will stay stuck. Here is what the chair looks like when all the fabric is removed.
There is batting, over horse hair, over the burlap and webbing structure of the chair. Why the painter’s tape? The padding and horse hair was in fine shape, so I wanted to keep it held in place so I could reuse it later. On a lighter note, check out what I found in one of the sides.
Haha, ick! Makes you wonder what sort of vermin are hiding in your own furniture . . .
The chair sat that way for a week or two, and every few days I would spend some time pulling out the remaining staples and nails. I don’t have any fancy tools for this, just a screwdriver and pliers. It’s a tiring job, but the more nails you can remove the better. It gives you more clean area for your own staples and nails you will use later when it comes time to add the fabric.
Side note, I keep the nails I pull out. They come in handy in the stapling process when you’re trying to attach fabric in a tight spot where the staple gun won’t fit.
After removing the staples and nails, I painted the frame. My plan starting out was a light gray wash look, which I achieved through dry brushing. I wrote about that process here if you missed it.
I loved the way the finish turned out, but it just didn’t look right with my chosen fabric. I didn’t want to buy new fabric, so I decided to change the paint. I took a wet rag and wiped off about half of the paint, focusing on leaving in the cracks of the frame. I then painted one light coat of ASCP Aubusson Blue. On top of the blue, I dry brushed again a little of the ASCP French Linen. After the paint, I wiped down the chair again, exposing a good bit of the wood. The result was the perfect finish–the blue highlighted the fabric better, but the gray and wood poking through added depth and kept the finish from being too bright. Happy with the frame now, I moved on to the fabric.
Lay out your fabric, paying attention to pattern if any. Then lay out the pieces removed from your project. To give myself a little more wiggle room, I cut around the pieces about another inch.
You can skip this part and just lay your fabric up on the furniture, staple some and start cutting it out. But that gets messy and I have found wastes fabric. Making a pattern keeps there from being too much excess fabric getting in the way while you work.
Once all the fabric pieces were cut, I started stapling them onto the chair. Always start with the front, leaving the back exposed. You need access to the back to find the “guts” of the chair where you will be stapling on your fabric.
This is the bottom seat cover, being stapled on to the top of the wooden base. You can see the holes from the original nails down by the blue paint . . . keep that area open for your back fabric staples.
The front back and sides came next. I laid the fabric pieces out on the front, then tucked the ends down through to the back.
Here is that side panel being pulled through. I actually flipped up this piece and stapled it to the unpainted wood frame piece above. Staple a few anchor staples in the back, then moving to the front, pull the fabric tight and staple around the panel.
This is the front seat, and like I mentioned above, it was handy in places to reuse those upholstery nails. The staple gun generally won’t get the staples all the way in, so you need to tap them in with a hammer. I have a little hammer that I use. When working in tight places, the smaller the hammer the better.
Once the front panels are all pulled tight and stapled on, you can start on the back. This where it gets fun because you cover up all those chair guts and front staples.
When all the stapling is finished, it’s time to trim off any excess fabric with some sharp sewing scissors, then add your trim with a hot glue gun. The trim does wonders for hiding any small errors.
I like to apply the glue to the trim, hold it out from the piece with my left hand, and gently push it into the frame with my right thumb. You don’t want to pull the trim tight, but keep it loose so you can maneuver it into corners. I have given myself some second degree burns from this process before, and I’ve learned holding it out this way protects my hands and the fabric the best.
I have no professional upholstery skills, and I know those who do would probably read this post and shake their heads . . . but when you’re a DIY-er, you learn as you go and do the best you can, sometimes improvising along the way. I think it turned out fabulous and was a fun, rewarding project. I’ll end with a few more “after” shots. Thanks for following along with me!
Linking up to:
Silver Pennies Sundays, Make it Pretty Monday, Give Me the Goods,
Metamorphosis Monday, Masterpiece Monday, Mod Mix Monday,
The Sunday Showcase Party, Motivate Me Monday, Made by You Monday,
That DIY Party, Project Inspired, Nifty Thrifty Tuesdays, Inspire Me Tuesdays,
Tuesdays Treasures, Anything Goes, Tweak it Tuesdays, The Scoop,
History and Home Link Party, Be Inspired, Wow us Wednesdays,
Wonderful Wednesday Blog Hop, Wow Me Wednesday, Cast Party Wednesday,
One Project at a Time, Power of Paint Party, Tutorial Tuesday, Chic By You,
Whatever Goes Wednesdays, Centerpiece Wednesdays, Be Inspired @ Common Ground,
All Things Thursday Blog Hop, Treasure Hunt Thursdays, Furniture Feature Friday,
Fridays Unfolded, What Have you Redone Friday?, Linky Party Palooza,
Funky Junk Party Junk